Zhone ETHX-DS3-2-LT Specifications

1 ETHX-DS3-1-LT and ETHX-DS3-2-LT DS3 EtherXtend Access Device Installation Instructions Document Number ETH3-A2-ZN10-00 May 2007 Contents Softwa

10 LED Indicators Table 2. LEDs (1 of 2) LED State Indication Additional Information Pulsing Green Standard operation Traffic is flowing wit

11 Table 2. LEDs (2 of 2) LED State Indication Additional Information Flashing Green* DS3 connection is established and active Traffic is flow

12 Web Interface The network extender’s integral web management lets you configure and monitor the network extender using a standard web browser.

13 Web Interface System Requirements  Web Browser – Required for running web management. Compatible web browsers include, but are not limited to,

14 192.168.254.251 (for a subscriber unit) into the Address field and press Enter. The web server opening screen appears. 10. Click on >> N

15 From this screen you can: Click on . . . To configure . . . Management Config. IP Address, Subnet Mask, Default Gateway, Inband Management

16 Configure Provider or Subscriber Mode To reconfigure a unit from provider to subscriber mode, open the web management home page as described ab

17 Command Line Interface The network extender can be managed with a Command Line Interface (CLI) through either a direct PC to COM (Communication)

18 Logging Into the CLI Once your terminal emulation program has been launched, device information is displayed, followed by a request for usernam

19 Resetting the Network Extender to Factory Defaults The network extender supports a reset process that may be used to delete the current configur

2 Software and Firmware License Agreement ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS, YOU MAY USE THE SOFTWARE AN

20 Connector Pin Assignments Ethernet Pin Assignments Table 3. Ethernet Pin Assignments Pin Function Pin 1 Rx+ Pin 2 Rx– Pin 3 Tx+ Pin 4 no

21 DB9 to 8-Pin Modular Adapter Pin Assignments To connect the COM port to the DB9 serial port of a PC, use an adapter wired as shown:

22 Specifications Specifications are subject to change without notice. Table 5. Specifications Specification Criteria Bandwidth/Distance Up to 4

23 EMI Notices United States – EMI Notice: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuan

24 Service and Repair If trouble is experienced with this equipment, please contact your local sales representative, service representative, or dis

25 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2.

26 Product Documentation Online Complete documentation for Zhone products is available at www.Zhone.com. Select Service & Support then select D

27 Copyright 2007 Zhone Technologies, Inc.. Printed in U.S.A.

28 * ETH3-A2-ZN10-00*

3 5. Except for the Product warranty contained in the manual, the Software is provided “AS IS” and in its present state and condition and Zhone

4 Introduction to ETHX-DS3-1-LT and ETHX-DS3-2-LT Zhone's ETHX-DS3-1-LT and ETHX-DS3-2-LT are loop bonding Ethernet extenders that provide up

5 Package Contents Unpack and Inspect the network extender. If there is any visible damage, do not attempt to connect the device. Contact your sal

6 Powering Up the Network Extender The DC power terminal block on the network extender has five terminals: two positive, two negative, and one with

7 Power Connection – AC Power 1. The AC power supply is shipped with the power terminal strip already attached. No AC power supply other than

8 Connecting the DS3 Lines The primary feature of the network extender is loop bonding capability, although both the provider and subscriber units

9 2. Verify all connections: the DS3 LINK/ALARM LEDs on the front of the network extender will pulse green to indicate the connections are establi